Deadlift Bars Comparison

Share:

Dedicated deadlift bars are becoming a big thing. 

I’ll be comparing a few popular power bars specifically for how well they perform as dedicated deadlifting bars for intermediate and advanced lifters.

Deadlift bars are a specialty type of power bar that caters specifically to deadlifts. It makes sacrifices in other areas when necessary to make it even better for deadlifting. 

Every one of the bars I’m reviewing here are really nice bars. If they were crap, I won’t include them. And hopefully I’ve included all the top ones.

What would a perfect deadlift bar be like?

Killer Grip

Aggressive knurling is a must.

Eventually, every lifter learns that the weak point in his deadlifting game is his grip. His fingers start to slip. 

Aggressive knurling doesn’t just mean it’s cut deep. If 

Knurling is a whole science in itself. 

Tacky Finish

The finish/coating of the bar needs a certain amount of “tack” to it to keep your hands from slipping too easily.

Chrome is notorious for getting slippery when wet. It’s just too smooth. Black oxide has a good amount of tack. Black zinc is also good, similar to black oxide. Everything but chrome can give you a good grip. Bare steel has also become popular.

Black oxide and zinc can both wear off with enough use, leaving bare steel underneath. This is not unusual. 

Thin Finish

The other thing to keep in mind with the finish is how thin it is. The thinner the better. A thick finish will fill in part of the depth of the knurling. Why go to all that trouble cutting deep knurling if you’re just going to fill it back in?

IPF Knurling Marks

This isn’t the knurling but the non-knurled rings spaced 810mm apart for the International Powerlifting Federation specs. The spacing here doesn’t matter if you’re using the same bar all the time, but if you aren’t, it helps to know for sure that you’re holding the bar in the same spot each time. Having a powerlifting bar with IPF spaced rings is most appropriate and consistent.

Extra Long Shaft

Normally, powerlifting bars have a grippable shaft length of around 52″. This way the shaft fits on a 48″ / 120cm wide olympic bench rack or power rack with some room for slop before the sleeves hit. The overall length of the bar is roughly 86″ / 7ft / 220cm. 

A few of the bars here have an extra long shaft, and the sleeves are the same length as other power bars. The long shaft isn’t needed for grip. I mean, some athletes have a wide grip, but deadlifts are not one of those wide grip exercises. What the long shaft does is flex more, and that helps spread the load over time as you lift off the floor, giving you an extra advantage of not heaving to pull 100% of the weight from the very bottom.

That being said, you do have to be lifting a lot of weight for the steel to start to flex. It varies, but let’s say 315 lbs / 140kg with a sumo grip (narrow grip, hands between legs), and 405 lbs / 180kg with a conventional grip. If you’re new to this, those numbers just correspond to three or four 45lb plates per side. If you aren’t lifting that much, you won’t get this benefit out of the bar.

Thin Diameter Shaft

The other thing about the shaft is the diameter should be thinner than a traditional 29mm powerlifting bar, or even a 28mm weightlifitng bar. A thinner bar is easier to get your hands around. To illustrate this, try pulling on a 2″ pipe that you can’t even get your fingers around to touch your thumb. Your grip fails REALLY quickly. Fat bar training is a whole different area of training, where people use 1.5″ and 2″ bars to work their grip strength.

27mm is what the manufacturers have settled on to provide for the strongest grip for average size hands. Strength of the steel also becomes an issue with thinner bars. They could certainly make 25mm bars just as they do for women’s weightlifting bars, but you have to consider the amount of weight typically used for women’s cleans vs. men’s deadlifts, and how strong the bar needs to be for them accordingly. Deadlifts can get pretty heavy. 

Quick Chart

  Rogue Ohio
Deadlift Bar
Texas Power Bar Texas Deadlift Bar Okie Deadlift Bar Okie Extreme
Finish Bare Steel or Black Zinc Black Zinc Black Zinc Bright Zinc Bare Steel
Diameter 27mm 28.5mm 27mm 27mm 27mm
Tensile Strength 190,000 PSI 180,000 PSI 186,000 PSI ? ?
Knurling Feel Aggressive Aggressive Aggressive Aggressive Aggressive
Center Knurling No Yes Yes Yes Yes
Length 90.5″ 84″ 90.5″ 90.8″ 90.8″
Flex High Low High Medium Medium
Price $295.00 $283.00 $399.00 $369.00 $519.00

 

Detailed Comparison

ROGUE OHIO DEADLIFT BAR

rogue ohio deadlift bar features

This is the new popular specialty deadlift bar. It just came out in 2016, making it much newer than the others. I’d call that a good thing. Rogue knows what they’re doing. They put real research into their equipment. The employees lift. You won’t find anyone saying that they bought something from Rogue that was low quality. 

This video really shows the flex of these extra long 90″ bars. He also talks about the knurling and how it really isn’t that bad on his hands despite going over 400 lbs.

But the flex on this bar is not as high as the Texas Deadlift Bar, further below. The Rogue Deadlift Bar and the Okie Deadlift Bar are about the same in this regard.

The knurling feels a lot like the Texas Deadlift Bar. They cut it really deep and round off the peaks, making it grip really well without too much bite.

 

TEXAS POWER BAR

texas power bar end cap

 

The classic bar manufactured by Buddy Capps. The end cap ohas the state of Texas logo. As you can imagine, it’s made in Texas. (Capps is not the same as CAP, a Chinese manufacturer… And not to be confused with the end “caps” as noted above. We need more words!) This bar is known for its deep, pointy knurling. See below. This kind of knurling provides a killer grip, but there’s a reason most bars out there don’t have it: it can hurt with a lot of weight. But there’s no denying how well it grabs onto your palms to keep from slipping. That’s the whole appeal of it.Texas Power Bar knurling

 

The knurling pattern is an important thing in that it’s not only about how deep the knurling is but how how flat or pointy the tops of each diamond are as a result of the knurling process (space between knurls and depth of cut). As shown, you can see that it does leave flat tops, but compared to other bars this is still fairly pointy and deep.

Other than that, it’s the quintessential power bar. 28.5mm shaft, 7ft length, black zinc finish. It’s a popular bar that some people feel is the best one they’ve ever had.

The sleeves are 15″ long, which is about average. Running out of length on the sleeves on any of these bars is not normally an issue unless you’re using bumpers (which are thicker than iron plates) or you’re a beast.

This is a popular bar still, and for years it’s been used as a deadlift bar. The thing is it is a very stiff bar. You won’t get any flex out of it unless you’re putting up huge numbers, and even then it’s minimal. So it’s not a specialty deadlift bar, but plenty of people love it for deadlifts, along with presses and squats. 

If you want a more dedicated deadlift bar, well, that’s why there’s their other model below…

 

TEXAS DEADLIFT BAR

Texas Deadlift Bar end cap

The Texas Deadlift Bar has huge inside collars and a loadable sleeve length of 14 3/8″.

The 56″ shaft is significantly longer than the typical 52-53″ of other power bars. 

The longer shaft and big collars have the effect of providing more flex to the Texas DL bar on your pull before it clears the floor, because the plates are further out and there’s a longer shaft to flex. This was an intentional design feature. These 7.5ft deadlifting bars create a problem if you have an 8ft residential ceiling to content with and you want to store your bar in a vertical bar holder. If you’re careful you should be able to just barely store a 7ft bar that way. The knurling is the same as the Texas Power Bar (no surprise there). See the close-up image above.

Texas Deadlift Bar has been reported to have the most flex, about the same as the Rogue Deadlift Bar. 

Competitive powerlifter Jonathan Harder did this detailed video review of the Texas Deadlift Bar and Okie Deadlift Bar, focusing on the dimensions, finish and flex. Keep in mind that the finish isn’t the same as the ones we have links to here that are currently in production, but I believe the rest of the details still match up.

 

OKIE DEADLIFT BAR

Okie Deadlift Bar

The Okie was the FIRST deadlift bar made to these kind of specs. Its other claim to fame is it has been used in tons of local, state, national and international lifting competitions over the years. In other words, it’s a proven favorite of heavy lifters.

The design is perhaps dated, so be sure to see the details on the upgraded Okie Extreme Deadlift Bar, further below.

The Okie Deadlift Bar has 15 15/16″ sleeves, pretty long. You’ll fit another plate on each side compared to the others.

This bar is pretty rare. You can only get it online from a couple places like Lifting Large.

Like the Texas DL bar, it has a longer shaft. The point of the longer shaft on these bars is so they will flex more, so you don’t have to lift the entire load starting at the bottom position. It does take a lot of weight for this flex to come into play.

I couldn’t get a tensile strength rating for this, but my guess is it’s got to be right about the same as the others. The strength isn’t going to be an issue.

The flex is slightly less than the Texas DL bar and Rogue Ohio Deadlift Bar, and that’s probably because of the larger inside collars of the Texas DL bar as Jonathan discusses in the video in the section above.

As far as knurling goes, it feels pretty similar to the Texas DL bar, but it’s not quite as deep so is a little easier on your hands between the two.

Here’s something interesting. This bar doesn’t have bushings in the sleeves. The sleeves are just steel on steel. For deadlifts, you know, maybe that’s a good thing I guess. You don’t want the bar to rotate out of your hands. 

I’m told the Okie has pinned sleeves. Rogue is definitely snap ring. It’s just the method used to secure the sleeves. Rogue talks about it like snap ring allows for a better spin, but I don’t know. It’s hard to get info on the Okie bar. The pic above makes it look like it’s got a snap ring, as otherwise you can see the pin. 

 

OKIE EXTREME DEADLIFT BAR

Okie Deadlift Bar

 

The Okie Extreme is an upgrade over the original Okie, with a few major changes:

  • Snap rings – A little better spin than pinned sleeves.
  • Bronze Bushings – Definitely for better spin!
  • Bare steel shaft for a better grip.
  • Zinc plated sleeves for less scratching from plates and better rust prevention.

This bumped up the price of the Extreme by $120.

The bare steel shaft is technically removing a feature, but it was done because I guess they found so many lifters who prefer bare steel over zinc or any other plating/coating.

 

Conclusion

All of these bars are great for deadlifts, depending on your situation, which is why I included them and not the hundred other bars on the market. 

Here are the quick reasons you would go with each of them.

Rogue bars are popular for a reason. The 7.5ft Rogue Ohio Deadlift Bar is the newest one of the bunch and is getting great reviews. Everything about it is superb as a deadlift-only bar. It’s the only choice if you want bare steel, rather than a coating like black oxide.

The 7ft Texas Power Bar is a classic pick if you will use it for other exercises. It’s a good all-around bar. It doesn’t have the crazy extra length of the dedicated deadlift bars. 

The 7.5ft Texas Deadlift Bar is what Rogue appears to have modeled theirs after. If you’re going to use it for something other than deadlifts, you might want the center knurling of this one. Is that worth the extra $100 to you? Or if you have any reason not to go with Rogue, this is a great pick.

The 7.5ft Okie is becoming dated, but it was the original groundbreaking design, and there’s a certain fame behind it. There are some old rusty Okies out there that people love too much to replace. If a powerlifting meet you’re competing in will be using the Okie, which is entirely possible, then it’s sure nice to practice your lifts on the exact same bar.

The 7.5ft Okie Extreme is more like the Rogue and Texas DL bars than the original Okie. The price is pretty high, so I think you’re partly buying it for the proven brand name.

 

Are there any fantastic deadlift bars I haven’t included here that you feel should be on the list? Let me know, and I’ll look into it!

  • Was this Article Helpful?
  • yes   no
Share:

Leave a reply