The Top 4 Budget 20kg Olympic Weightlifting Bars

By | 2018-05-11T17:51:14+00:00 May 10th, 2018|Categories: Equipment Guides|Tags: , , , , , |0 Comments

 

CONTENTS

  1. Intro
  2. What Makes a Good WL Bar
  3. The Bars
    1. Rogue 28mm Training Bar
    2. York 32110
    3. Rep Gladiator
    4. Fringe WL Bar

Intro

This is for olympic weightlifting bars (often called WL bars for short) that are best for doing the clean and the snatch. For powerlifting bars for deadlifts, squats and bench press, see the powerlifting bars comparison. Or learn about the difference between the two.

With the rise of olympic lifting in Crossfit, and other lifters incorporating olympic lifts into their existing routines, more and more people are in search of bars that are more appropriate for olympic lifting than the traditional power bars that have been marketed towards bodybuilders, casual lifters, and powerlifters.

Olympic weightlifting bars are used frequently at olympic lifting gyms, Crossfit boxes, the Olympic Games or anywhere that lifters may be doing olympic lifts. They are made to be springy at high loads to facilitate explosiveness, prevent a high shock load for the lifter, and absorb the shock of being dropped. 

It isn’t necessary to get a $500-1000 bar just to have a good tool for olympic lifts. Bars in that range are typically IWF certified bars, which carries a huge bump in the price tag. Plus, those bars are normally not appropriate for anything but practicing a few heavy singles, because the knurling is meant to really grab onto your palms to help you get the barbell up for that one heavy lift that really counts. For learning the lifts and doing regular workouts, you’re better off with a medium to soft knurling that won’t eat up your hands.

The knurling further down the bar should extend to the end of the shaft to accommodate tall users with the maximum width snatch grip, but this isn’t the case on all bars.


What Makes a Good Budget Olympic Weightlifting Bar

Weightlifting bars typically have a number of attributes that separate it from any number of other bars you might encounter.

More Flexible Steel

A good flex facilitates the “whip” desired for pulling heavy cleans off the floor. It makes for a smoother lift off the floor, the way the bar begins to bend upward, ever so slightly, until you pull hard enough that it completely lifts up. This is not noticeable until you get over 300 lbs or so and have done cleans on a WL bar and power bar to feel the difference. With heavier and heavier weights, the difference is huge. A power bar gets really hard to do cleans with.

The second factor in the flex is catching the bar on your shoulders in a clean. With good form the impact on your shoulders is minimal. You can test this yourself at very light weights. Load a couple 25s on, do a messy power clean by catching the bar hard on your shoulders, and it will shake, relieving the impact. Do this with a stiff 30mm power bar and you can see what I’m talking about right away. Which do you prefer? Yep, now you can never go back.

The third point at which the flex helps is bouncing out of the hole as you catch in a full squat clean. The bar tips flex down with you and whip back up as you push yourself out of the hole. Powerlifters specifically do not want this flex, because their squats are slower and any whip will be too fast for them and throw them off. They need a slow, controlled squat that may take a few seconds to complete.

High Tensile Strength Steel

Nowadays it isn’t hard to find tensile strengths over 200,000 PSI (pounds per square inch). In years past that was considered extreme and quite rare.

That isn’t to say that you have to get over 200,000 PSI. Bars well under that should not bend either. Moderately priced bars are all made to hold up to frequent drops with bumper plates onto rubber flooring or a platform. That’s quite a shock load, but it’s not nearly as bad as dropping a bar on the safety pins of a rack, which is likely to bend any bar (or the safety pins – something has to give). 

When we talk about bending, we’re talking about a permanent bend, effectively rendering the bar useless or at least extremely annoying to use. Flex under load is normal and is part of what saves the bar from developing a permanent bend. Along with high tensile strength, that’s what keeps the shaft going strong.

The steel formulations today are better for high tensile strength bars for olympic weightlifting, basically so that you can get a high tensile strength bar that isn’t super stiff because of it. 

Snap Rings or Roll Pins to Secure the Sleeves

Good WL bars have the end sleeves secured with either a snap ring (also called a retaining ring) or a pin hammered through a hole going the width of the sleeve, which is the method York Barbell in particular prefers. Most everyone besides York does the snap ring method.

One of these methods is to ensure the sleeves don’t break loose and fall off the bar after enough drops with bumper plates. Dropping a bar is tough on it, even on 3/4″ rubber flooring. Good bars can hold up fine. On the cheapest bars, usually sold for around $100 or included in a 300 lb weight set, you’ll find an allen bolt, which you need an allen key (hex key) to tighten. And tighten it you will. These are notorious for coming loose over time. Even if you apply Loctite to it, it will probably just break on you. 

Snap ring on the end of a bar

Snap ring example – See the two holes on top that the special pliers hook into to pull it into place.

Medium to Soft Knurling

The knurling is the texture that cut into the shaft of the bar to help you grip it better. There’s a whole science to it and different steps involved. 

How ever the maker decides to create the knurling pattern and texture, which we don’t need to go into here, the end result needs to be that you can get a good grip without the knurling damaging the palms of your hands over many reps. 

No Center Knurling for High Rep Workouts

All bars have knurling over most of the length of the shaft. Some bars have a section of about six to nine inches of knurling in the center of the bar, while others are smooth in that area.

IWF competition rated bars are required to have center knurling as per the IWF spec that has been in place for decades, ever since the one-handed snatch was a competition lift and you needed to actually grip the center of the shaft.

While lifters doing other movements might like the center knurling, for the olympic lifts it serves no purpose anymore but to scratch the front of your neck during cleans. For this reason, lifters concentrating on olympic lifts prefer no center knurling.

910mm Spaced Ring Marks

Every bar has a 1/4″ wide smooth mark in the knurling where you place your hands. IWF spaced markings are spaced for olympic weightlifting and are 910mm apart. Lifters grip in various spots depending on their body size, but the knurl marks at least provide a reference point to help them guide their hands into the right spot for them.

In recent years, many manufacturers have added IPF 810mm spaced marks as well, for a pair of “dual” marks 5cm away from each other. They just help you position your hands consistently. That’s all there is to it. 

28mm Shaft Diameter

Not to be confused with the size of the sleeve where the weights go, which is always 50mm (1.97″) on a high quality bar.

Here we’re talking about the shaft that you grip. For the optimal grip, 28mm is the best size for men’s bars. It makes for a good pulling grip.

The diameter is also major factor in the amount of flex that the shaft has, which is very important for cleans. See the info further above on flex.

Sensitive and Smooth Rotation

How sensitively and easily the sleeves spin is very important for olympic lifts so you can transition between the pull and the catch without tweaking your wrists. 

Manufacturers like Eleiko have settled on up to 10 needle bearings per sleeve for their very best competition bars. 

For budget WL bars you don’t need that many. Fewer bearings will reduce the spin, as will a combination of bushings and bearings, but it’s still good.

Bronze bushings are the next step down. Some WL bars we feature below have bronze bushings. Lubricated bronze slides well against steel (I think it has something to do with the dissimilar materials, such that bronze actually slides against steel better than steel-on-steel does). 

Shaft Finish

The finish, or outer coating, applied to a bar makes a difference in its durability, tackiness, rust resistance, and how well it holds chalk.

Chrome
Chrome plating looks nice and wears well from repeated banging on a rack. All of the bars we sell, including our standard 1″ bars, and virtually all of the high quality bars sold today elsewhere, have a hard chrome finish rather than decorative chrome. The cracking and flaking chrome you might see on old bars might be decorative chrome. Hard chrome has the lowest level of corrosion resistance in any finishes, other than bare steel (ie: no finish). The smoothness of chrome makes it slippery when your hands get sweaty, even over good knurling. Chrome can sort of get a bad rep because most of the economy 300lb weight sets include a cheap chrome bar which might be made with decorative chrome. And the last thing about chrome is it does NOT hold chalk very well in comparison to all the other finishes.

Black Oxide
This is a thin coating that feels almost like bare steel. It’s thin enough that it doesn’t fill in any of the depth of the knurling like chrome or zinc plating does. It also gives a better grip than chrome. And it helps prevent rust (anti-corrosion), but the anti-corrosion properties of black oxide are activated by oil, so you have to oil it once in a while. It scratches more easily than other finishes, so a bar used in a rack will immediately show signs of use from the metal-on-metal contact. It can also wear off simply from the abrasion of your hands against it.

Black Zinc
Like black oxide, it provides a good grip and prevents corrosion without the need to oil it as much. Zinc plating has a certain thickness to it, so it does fill in the knurling slightly like chrome does, making the knurling a softer feel. Zinc itself is a bright silverish color and the black coating is actually applied over the bright zinc. 

Stainless
Basically this is the most expensive and the best, in my opinion. It looks like chrome, but it isn’t a chrome outer coating, it’s chromium mixed into the steel, which we call stainless steel. It is extremely resistant to corrosion and feels like a nice bare steel bar. The texture of the knurling doesn’t get filled in at all by any coating.

Weight

7ft olympic bars are made to weigh 45lb or 20kg / 44lb. 

In this article we’re focusing only on the 20kg bars. IWF weightlifting meets always use kilos, as do IPF powerlifting meets. Therefore the bars used for weightlifting tend to be calibrated to 20kg or pretty close to it. 


THE BARS

These WL bars are in the affordable price range of $200-400 and are suitable for beginner and intermediate lifters who don’t need a competition level bar.

Too pricey? Check out our Best Olympic Bar Under $200 article for some general-purpose bars that will work.

Also keep your eyes out for our upcoming article (within a week) on women’s 15kg olympic weightlifting bars.

Rogue 28mm Training Bar

Shaft Diameter: 28mm Center Knurling: No
Shaft Finish: Black Zinc Ring Marks: IWF
Tensile Strength: 190,000 PSI Sleeve Surface: Grooved
Sleeve Spin: Bronze Bushing Made In: USA
Knurling Feel: Medium Weight: 20kg

Rogue’s 28mm Training Bar uses the same 190,000 PSI steel shaft as all their other men’s 7ft bars. That makes production a little easier!

Rogue stands behind their products, and you know they’ll be around for years to come. It’s one reason people often go for Rogue when in doubt.

Plus, Rogue makes their bars in their own facility in Columbus, OH. That makes it the only one on this page made in the USA.

It’s also the only bar here with bronze bushings. So this is questionable as a pure WL bar. Bronze bushings are only one step down from needle bearings, better than composite bushings as far as the sensitivity of the spin, if it’s constructed nice and tightly and lubricated right. If you’ve used a good bronze bushing bar and you’re ok with it as a WL bar, this could be a really good choice for you.

Price: $325 at Rogue

York 32110 North American Training Bar

Shaft Diameter: 28mm Center Knurling: No
Shaft Finish: Satin Chrome Ring Marks: Dual
Tensile Strength: 170,000 PSI Sleeve Surface: Smooth
Sleeve Spin: Bearings Made In: Canada
Knurling Feel: Medium Weight: 20 kg

York Barbell has been involved in olympic weightlifting since their inception in 1932. They revised their bars a year or so back without changing the model numbers. For this one they removed the center knurling, which they previously had on all their men’s bars, added dual ring marks, and I think they may have started using a higher tensile strength shaft… My memory is bad on that last one.

They call this a “North American” bar. Not quite USA made. “Made sort of here” is the general effect they were going for. I was able to dig up that it’s made in Canada.

From the close-up shot you see York’s patented split-sleeve design. Dead giveaway it’s a York bar when you see that.

Price: $280 at Adamant Barbell

Rep Fitness Stainless Steel Gladiator Bar

Shaft Diameter: 28mm Center Knurling: No
Shaft Finish: Stainless Steel Ring Marks: Dual
Tensile Strength: 205,000 PSI Sleeve Surface: Grooved
Sleeve Spin: 5 Bearings Made In: USA
Knurling Feel: Medium Weight: 20 kg

The only stainless steel bar here! Plus, 5 needle bearings per sleeve… That’s 1 more than Fringe!

Rep still makes a chrome version of this bar too. Considering that the stainless steel version is not very expensive at all, you should not even consider the chrome version. Stainless does not get as slippercy as chrome. Being as stainless is a type of steel, not a coating, there is nothing to wear off or chip away. It feels very much like a bare uncoated steel bar, which it basically is, with the advantage of superior corrosion protection of stainless steel. So you get the full effect of the texture and knurling of the bar.

Rep Fitness has been in business in Denver, Colorado (10 miles from Rage Fitness) since 2012, and they have earned the respect of the Crossfit crowd with their high quality equipment.

Rep has always had favorable reviews online and are good with answering questions. Rep’s equipment seems to be nearly as high quality as Rogue. Rep isn’t a “budget” option that cuts any corners.

Rep’s prices for larger orders are particularly competitive vs some others who offer free shipping on all sized orders. On small orders Rep normally isn’t as competitive, although in this case for a stainless steel WL bar they’re basically the only choice in this price range! If you’re in the market for additional stuff like bumpers, once you get one or more pallets worth of stuff you’re taking advantage of the fact that you’re paying actual shipping costs instead of a padded amount added to all products for “free” shipping on single-product orders. 

Price: $269 at Rep Fitness

FringeSport Weightlifting Bar

Shaft Diameter: 28mm Center Knurling: Yes
Shaft Finish: Matte Chrome Ring Marks: IWF
Tensile Strength: 216,200 PSI Sleeve Surface: Grooved
Sleeve Spin: 4 Bearings Made In: Taiwan
Knurling Feel: Medium Weight: 20 kg

This bar is the #1 bar that Fringe makes for olympic weightlifting. All their other bars are made for either powerlifting dual-use. This one is their only bar with 4 needle bearings per sleeve, IWF-only ring marks, and it has the most whip out of all their bars despite the ultra high 216,000 PSI tensile strength.

As far as the “matte” chrome… I don’t think that there is any difference between matte chrome and satin chrome, which is what York calls it. The word “matte” has gotten to be a popular buzzword with Rogue and others, with their popular matte finishes on power racks, etc, and the “Matte Black Friday” sale. Basically a less glossy chrome that looks more like stainless steel. As if it weren’t already hard to tell the difference! Mirror-like chrome is one thing, but when they start using this satin chrome I have a hard time identifying what it is on an unknown bar.

Fringe’s guarantee is the best in the industry. It’s more than just a warranty against defects. They offer a full 1-year guarantee. Return it for any reason within a year and get your money back! Or within 30 days they’ll even pay the return shipping. 

Price: $399 at FringeSport

 

Got any questions about these bars? Leave a comment and I’ll see if I can help!

  • Was this Article Helpful?
  • yes   no

About the Author:

David Kiesling
David founded Adamant Barbell in 2007. He is into weight training, Crossfit, nutrition, hang gliding, snowboarding, archery and hackysack. He also owns a hang glider repair business.

Leave A Comment